Important Plumber Tips for Bathtub Installation
Important Plumber Tips for Bathtub Installation
Blog Article
Almost everyone has got their own unique piece of advice about Tools You Need to Install a New Bathtub .
Mounting a tub isn't precisely brain surgery, however it does require solid plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a new one is likewise a moderately difficult project. If the old tub is easily obtainable, the job can relocate easily; if you need to open up a wall to get rid of the old bathtub and also place the new bath tub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will certainly need a helper to move out the old tub and also embeded in the new one. See to it you have qualified yourself for the work and are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed project, it is much better to take into consideration employing one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This post will aid you install a new bathtub in your shower room if you have actually already purchased a new tub as well as don't require to change the arrangement of your previous water system pipelines.
Your tools and also product list need to make up the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be quite bothersome as a result of the restricted access that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the continuing to be water that will come from the pipes. When the supply pipes have been removed, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from turning throughout this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washers remain in area in between the tap and the sink. Protect the tap in position with the supplier offered backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The former kind should be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Using both wooden boards under its feet, position the bathtub in the required position. The wooden boards are useful in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The next goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the bath tub until the level reads level.
To set up taps, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipe by making a compression join; after that do the exact same for the other faucet.
Switch on the water supply and also inspect all joints and also new pipework for leaks and also tighten them if necessary. Load the bath tub as well as likewise check the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bath paneling as explained in the supplier's user's manual. Tiling as well as securing around the bath tub should wait until the tub has been utilized at the very least when as this will resolve it right into its last position.
Getting ready for the Installment
First of all, the sustaining frame provided with the bathroom should be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets system to stop strain on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to fracture a rigid seal, causing the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with dampness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealers to assimilate your components as well as installations. They are sold in tubes and also cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealant can fracture fairly early if you do not think about this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the market. It is a good idea to fit the tiles making use of water-resistant or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that write-up about How to Install a Bathtub Yourself from a friend on a different blog. Enjoyed reading our article? Please share it. Help other people discover it. I am grateful for your time. Kindly visit our blog back soon.
Book Your Installation Report this page